400ML PURE EPOXY CHEMICAL ANCHOR EPX-100
Description:
EPX-100 is a styrene free pure epoxy anchoring adhesive supplied in a 400ml side by side cartridge. Resin and hardener sit in separate chambers at a fixed 3:1 volume ratio and are blended automatically through the static mixing nozzle as the adhesive is dispensed, so the installer never has to measure or hand mix. The cured mortar develops high bond strength in concrete and in dense natural stone.
It is used for post installed rebar, threaded rod anchoring and bolt fixing in structural work. Because it contains no styrene the odour is low, which makes it suitable for indoor work and confined spaces.
Recommended retail price: 480,000 VND per cartridge (VAT 8% not included). Two static mixing nozzles are included with every cartridge. Made in Taiwan, imported through official channels with full VAT invoicing.
- Material: Pure epoxy, styrene free
- Model number: EPX-100
- Size: 400ml side by side cartridge
- Mixing ratio: 3:1 by volume, blended automatically through the static mixer
- Resin base: Bisphenol A/F epoxy with silane and silica fillers
- Consistency: non sag putty, suitable for horizontal and overhead holes
- Flash point: resin above 125 degrees C, hardener above 74 degrees C
- Included: 2 static mixing nozzles per cartridge
- Carton: 20 cartridges, approx. 0.76 kg per cartridge, approx. 15.8 kg gross
- Storage: dry cool place at 10 to 40 degrees C, out of direct sunlight, original packaging
- Origin: Made in Taiwan, R.O.C., brand new, officially imported
- Styrene free pure epoxy means low odour and a better working environment indoors and in enclosed spaces.
- Separate chambers plus a static mixer remove the largest source of on site error, an incorrect resin to hardener ratio.
- Non sag putty consistency holds in horizontal and overhead holes until the rod is inserted.
- Bisphenol A/F epoxy with silane coupling agents gives high adhesion to both concrete and steel.
- High flash points and no UN dangerous goods classification under ADR/RID, IATA and IMDG simplify shipping and site storage.
- Two mixing nozzles supplied with every cartridge, so a paused job can restart with a fresh nozzle.
- Post installed rebar connections in columns, beams and slabs during repair, renovation or structural extension.
- Threaded rod and anchor bolt fixing into concrete for steel structures and machinery bases.
- Anchoring into dense natural stone.
- Load bearing fixings in general construction where a high strength bonded anchor is specified.
Installation note: clean the drilled hole thoroughly with a blow out pump and brush before injecting. Discard the first portion of adhesive until the extruded material shows a uniform mixed colour.
| Product | Unit | Retail price (VAT excluded) |
|---|---|---|
| EPX-100 400ml pure epoxy (2 mixing nozzles included) | Cartridge | 480,000 VND |
| G34-400LA caulking gun for 400ml cartridge | Piece | 850,000 VND |
Prices exclude 8% VAT. Dealer and bulk order discounts on request.
The G34-400LA is a heavy duty applicator dedicated to 400ml two component cartridges, red body, sold separately.
To order: +84 931 176 176 or +84 9 6161 0202. Email: [email protected]
Documentation
- Certificate of Origin issued by the Kaohsiung Chamber of Commerce, Taiwan.
- Full manufacturer MSDS available on request.
- Officially imported with customs clearance and full VAT invoicing.
Safety
- Wear gloves and eye protection; avoid skin and eye contact with uncured adhesive.
- Work in a ventilated area and keep away from heat and open flame.
- Skin contact: wash immediately with plenty of water and soap.
- Eye contact: rinse with clean water for at least 15 minutes and seek medical attention if irritation persists.
- Keep out of reach of children.
